收藏本站
23A640/23K640
3.0
PIN DESCRIPTIONS
3.5
Hold (HOLD)
The descriptions of the pins are listed in Table 3-1.
The HOLD pin is used to suspend transmission to the
23X640 while in the middle of a serial sequence without
TABLE 3-1:
PIN FUNCTION TABLE
having to retransmit the entire sequence again. It must
be held high any time this function is not being used.
Name
PDIP/SOIC
TSSOP
Function
Once the device is selected and a serial sequence is
underway, the HOLD pin may be pulled low to pause
further serial communication without resetting the
CS
SO
V SS
SI
SCK
HOLD
V CC
1
2
4
5
6
7
8
Chip Select Input
Serial Data Output
Ground
Serial Data Input
Serial Clock Input
Hold Input
Supply Voltage
serial sequence. The HOLD pin must be brought low
while SCK is low, otherwise the HOLD function will not
be invoked until the next SCK high-to-low transition.
The 23X640 must remain selected during this
sequence. The SI, SCK and SO pins are in a high-
impedance state during the time the device is paused
and transitions on these pins will be ignored. To resume
serial communication, HOLD must be brought high
while the SCK pin is low, otherwise serial
3.1
Chip Select (CS)
communication will not resume. Lowering the HOLD
line at any time will tri-state the SO line.
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
When the device is deselected, SO goes to the high-
impedance state, allowing multiple parts to share the
same SPI bus. After power-up, a low level on CS is
required, prior to any sequence being initiated.
Hold functionality is disabled by the STATUS register
bit.
3.2
Serial Output (SO)
The SO pin is used to transfer data out of the 23X640.
During a read cycle, data is shifted out on this pin after
the falling edge of the serial clock.
3.3
Serial Input (SI)
The SI pin is used to transfer data into the device. It
receives instructions, addresses and data. Data is
latched on the rising edge of the serial clock.
3.4
Serial Clock (SCK)
The SCK is used to synchronize the communication
between a master and the 23X640. Instructions,
addresses or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
pin is updated after the falling edge of the clock input.
DS22126B-page 12
Preliminary
? 2009 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
23K256T-E/ST IC SRAM 256KBIT 20MHZ 8TSSOP
23K640-E/P IC SRAM 64KBIT 20MHZ 8DIP
23KM-K743-99V MOTOR STEP UNI 56MM SQ 24V DL
24AA00-I/PG IC EEPROM 128BIT 400KHZ 8DIP
24AA01H-I/MS IC EEPROM 1KBIT 400KHZ 8MSOP
24AA025E48T-I/SN IC EEPROM SER 2K I2C 8-SOIC
24AA02H-I/MS IC EEPROM 2KBIT 400KHZ 8MSOP
24AA02T/ST IC EEPROM 2KBIT 400KHZ 8TSSOP
相关代理商/技术参数
23A640T-E/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:64K SPI Bus Low-Power Serial SRAM
23A640T-E/SN 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:64K SPI Bus Low-Power Serial SRAM
23A640T-E/ST 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:64K SPI Bus Low-Power Serial SRAM
23A640T-I/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:64K SPI Bus Low-Power Serial SRAM
23A640T-I/SN 功能描述:静态随机存取存储器 64K 8K X 8 1.7V SERIAL 静态随机存取存储器 IND RoHS:否 制造商:Cypress Semiconductor 存储容量:16 Mbit 组织:1 M x 16 访问时间:55 ns 电源电压-最大:3.6 V 电源电压-最小:2.2 V 最大工作电流:22 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:TSOP-48 封装:Tray
23A640T-I/ST 功能描述:静态随机存取存储器 64K 8K X 8 1.7V SERIAL 静态随机存取存储器 IND RoHS:否 制造商:Cypress Semiconductor 存储容量:16 Mbit 组织:1 M x 16 访问时间:55 ns 电源电压-最大:3.6 V 电源电压-最小:2.2 V 最大工作电流:22 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:TSOP-48 封装:Tray
23A683F075EH1H1 制造商:REGAL BELOIT 功能描述:Electrolytic
23A753F050DI1H1 制造商:REGAL BELOIT 功能描述:Electrolytic